A Rocking ship tall clock, a rare find attributed to the Paul Rogers School of Clockmaking in Berwick, Maine. 217125.
Everyone notices a tall clock dial that features some form of automation. When people come into view our inventory, clocks with automated dials are often the examples they comment on first. Automation comes in many forms. The most popular is the rocking ship, but we have owned clocks that feature Father Time or Chronos in the arch. This figure moves from side to side with the pendulum’s motion. Not too long ago, we sold a clock with a dial that depicted Adam and Eve, where Eve’s arm moves towards Adam as if handing him an apple. In the past, we sold clocks with a person’s or an animal’s face, and their eyes were automated. This motion displayed in automated dials is an attention-getter and a conversation starter. In truth, very few clocks feature this desirable feature. We look long and hard to find.
This iron dial was paint-decorated by a local ornamental artist who has yet to be identified. The artwork presents beautiful folk art quality. Dials like this are uncommon. This example has a very good color. The four spandrel areas feature floral themes. The use of yellow coloring stands out. There is also additional paint decoration in the center of the dial below the center arbor, where a calendar display is traditionally located. The spandrel borders are painted green. This design also frames the outer edge of the time ring. This ring is formatted with large Roman-style hour numerals. Arabic-style numerals are used to mark each of the five-minute markers. A subsidiary seconds dial is located in the traditional location below the hour “XII.” The lunette, or the arch of the dial, is the much sought-after feature of an automated rocking ship. This ship is cut from tin and moves or gently rocks from side to side with the pendulum’s motion. The boat is quite large and depicted fully rigged, under sail, flying an American flag proudly off its stern.
The weight-driven movement is of good quality. It is designed to run for an eight-day duration on a full wind. This clock will also strike each hour on a cast iron bell mounted above the clockwork. This movement is typical of the Rogers school of clockmaking in terms of its construction. The movement plates are not brass. They are constructed in cast iron and feature brass bushings. Cast iron was used to conserve brass, an expensive material to work with at the time. The Rogers in Berwick, Maine, is well known for constructing clock movements in this manner. We have owned many clocks that were constructed in this manner and were signed on the dial by one of several members of the Rogers family.
This is a very nice country case tall clock that exhibits long, narrow proportions. It stands approximately 82.5 inches, or 7 feet 8.5 inches, tall to the top of the brass center finial. It is 20.5 inches wide and 10 inches deep. This case is constructed in maple, and white pine is used as the secondary wood. The darker finish has been enhanced with protective wax.
This fine example stands on a cutout bracket base. The base section is fitted with an inset panel. The waist section is very long and narrow. The waist door is rectangular and trimmed with a simple molded edge. Another nice country detail is the multiple pegs found in the construction of the waist framing. Finely reeded quarter columns are fitted into the corners of the waist. These terminate into brass quarter capitals. The bonnet or hood is equipped with fretwork. The pattern is unusual and quite interesting. Three reeded finial plinths support this. Atop each plinth is a brass ball and spike finial. Fully turned and reeded bonnet columns terminating in brass capitals flank the bonnet door. This door is an arched form and is fitted with glass. It opens to access a locally painted arched-shaped dial.
This clock, a product of the late 18th century, was made circa 1795. Its creation is a testament to the craftsmanship and innovation of that era, making it a valuable piece of history for any collector or history enthusiast.
This clock is $7,500.
Paul Rogers was born in 1752 and died in 1818. He was a Quaker and an active member of the Society of Friends. The Quakers were known for their independence and devotion to hard work. They had established numerous small colonies throughout the more rural parts of New England. He was a very productive clockmaker who worked at his trade for nearly forty years. A few notable apprentices to Paul include his son Abner (1777-1809), Reuben Bracket (1761-1867), and John Taber (1796-1859). We have owned a large number of Paul Rogers clocks.
This clock is $7,500.
Inventory number 218104.
Paul Rogers was born the son of Isaac and Lydia (Varney) Rogers on June 26, 1752, in Berwick, Maine. He was the youngest of eight children. He was a Quaker, more appropriately called a member of the Society of Friends. The Quakers were a sect known for their independence and devotion to hard work and had established small colonies throughout the more rural parts of New England. Paul is often recorded as a “Clerk” in their meeting minutes. Paul was a very productive clockmaker who worked at his trade for nearly forty years. Many of his movements are constructed with cast iron plates and brass wheels. A few notable apprentices that Paul trained include his son Abner Rogers (1777-1809), Reuben Brackett (1761-1867), and John Taber (1796-1859). Paul Married Deborah Hussey of Kittery, Maine, on August 30, 1774. They had nine children. After clockmaking, Paul became a hatter and made and sold many hats throughout the nearby Maine Villages. Paul Rogers died in 1818.
